juni 20th, 2016 by stijgerart
made with a great team , Rachel Pedro Fergus and myself!

made with a great team , Rachel Pedro Fergus and myself!

Posted in sand sculpting having no comments »

april 19th, 2016 by stijgerart
A painting made with many cnc router tracks in a plate!

A painting made with many cnc router tracks in a plate!

image image

a capture and scan of an old cnc plate was made!

a capture and scan of an old cnc plate was made!

Posted in Uncategorized having no comments »

Art made with the new machine!

april 1st, 2016 by stijgerart

image image cnc art

Posted in Uncategorized having no comments »

final bits

maart 7th, 2016 by stijgerart
coating

before I put the machine in place, I put an epoxy coating on the floor, look so much better and easier to clean

back in place

back in place exactly how I wanted

IMG_3146

just some fine tuning on the sensors and its ready to go,

Posted in Uncategorized having 1 comment »

Re cable and sensors

maart 7th, 2016 by stijgerart
pannel

installing panels

IMG_3121

these panels are plexiglass, which is nice so you can see from the side!

Bridge

the bridge beams are in place and its time to put up the Y axis (bridge)

IMG_3130

bridge install

IMG_3132

adjust the cable

IMG_3136

Sensors arrived and ready to install

IMG_3138

yes also some ironing

IMG_3141

cutting bars

IMG_3142

instal the Sensors

IMG_3144

holders for the sensors along the X axes

Posted in Uncategorized having 1 comment »

arrival of the hight extensions 10 extra cm

maart 7th, 2016 by stijgerart

and here they are

the extensions for the Z axis

it was quite a work to tap 80 treads and to put them into place

but it was worth it every cm!

IMG_3112 IMG_3118IMG_3117IMG_3114 IMG_3113 IMG_3111

Posted in Uncategorized having 1 comment »

the CNC shop miller gets drawers

februari 27th, 2016 by stijgerart
cnc shop bench

all the drawer parts are nearly ready to go!

milling the front pannel on the backside

making slots for the sides and the bottom plates

fit fit

putting it together is now easy

IMG_3078

doing a last fit

done

done, now only just a little tweeking

drawers inn

I am loving this machine already! perfect

Posted in cnc having no comments »

getting started

februari 24th, 2016 by stijgerart

IMG_3009

Taking the Z axis and X axis off

IMG_3014 IMG_3016

Than we take off the 2  (low) side beams, and after  the 2 bottom beams in the end.

IMG_3020 IMG_3021

Now I cut the 2 ends. After this, there is NO WAY BACK!

IMG_3029 IMG_3028

With the extruded aluminium parts we saw off before I now use it for the table legs

Witch gives me a nice hight and good storage underneath.

Posted in cnc, cnc machine having no comments »

a serious shop cnc miller

februari 24th, 2016 by stijgerart

new cnccnc2016

 

I started with a design I made in ZBrush (top) than Rhinoceros (bottom)

Posted in cnc machine having no comments »

Change from wall router to table miller!

februari 24th, 2016 by stijgerart

Remember 5 years ago, I build a wall cnc router! that I can put up the wall at any time when I needed the space.

the problem was that the space was occupied by many project so that is was hard for me to change the router back to the floor!

so it ended up with not using the fantastic machine when I wanted.

Now i am decide to change it to a ready to go table cnc miller, LOLA is gonna be LOLITA (a little bit shorter)

I cut her total lengt down from 2800 to 2000 mm and I enlarge  her Z axis with 100 mm (witch is now 250 mm so far)

 

 

IMG_0989 IMG_0982 IMG_0983

 

 

 

 

 

 

IMG_0986the last week i was thinking to resize my big wall cnc to a serious work shop cnc table,  this is how I designed 5 years ago!

 

Posted in cnc machine having no comments »

About stijgerart

Wilfred Stijger is a multi talented artist from The Netherlands who works in 3D with different materials like: sand, ice and snow, wood and different synthetic materials.